Vibration Monitoring & Machine Protection Systems
1010 East Main Street, League City, TX 77573
www.stiweb.com / www.stiwebstore.com

Tel 281.334.0766
Toll Free 888.777.7213
Fax 281.334.4255

Sensors - Vibration Monitors - Vibration Transmitters - Protection Systems - Junction Boxes - BNC Switch Boxes - Sensor Cables - Mounting Hardware - Rotor Kits - Balancing Kits

Products

Accelerometer Mounting Hardware

STI offers a complete line of Accelerometer Mounting Hardware including Mounting Pads or Discs, Epoxy, NPT Adapters, Motor Fin mounts, End Mils and Accelerometer Extension Cables. All Accelerometer Mounting Hardware is in stock and ready for immediate delivery. STI also offers the CMCP250 Kit which includes all the accelerometer mounting hardware required to install up to 33 Accelerometers. The link below to our Application Note "Accelerometer Installation Guide" will help you decide on your installation method.

Accelerometer Installation Guide

	CMCP-Magnetic Base-01 Magnetic Mounting for any 1/4-28 Accelerometer. Our 2-Pole Magnetic Base for Accelerometers is 3/4" in Diameter and has an integral 1/4"-28 UNF mounting stud. Using rare earth magnets the pull strength is >20lbs. 2-Pole allows for mounting on flat or curved surfaces such as bearing caps.
	CMCP200 Accelerometer Mounting Pads For epoxy mounting to machine - 1/4"-28 threaded hole. Our stainless steel mounting pads are used to provide a flat surface for mounting accelerometers. They may be stud or epoxy mounted. They are available in magnetic and non-magnetic versions and with and without 1/4"-28 UNF threaded hole.
	CMCP203 Pipe Thread Accelerometer Mounting Adaptor Converts 1/4"-28 accelerometers to 1/4", 3/8", 1/2" or 3/4" NPT. CMCP203 Pipe Thread Adapters allow you to make use of existing 1/4", 3/8", 1/2" or 3/4" NPT holes on your bearing cap. They provide a smooth surface and a 1/4"-28 UNF threaded hole for mounting accelerometers.
	CMCP205 Accelerometer Motor Fin Mounts Painless solution for mounting accelerometers on cooling fins. STI's CMCP205 Motor Fin Mounts are used to mount accelerometers between electric motor cooling fins. Epoxy is used to hold them in place between the fins. They provide a smooth mounting surface for accelerometers and are provided with a 1/4"-28 UNF tapped hole.
	CMCP206 Adhesive Filler For Accelerometer Motor Fin Mounts - 50 ml CMCP206 Adhesive Filler is used to permanently mount CMCP205 Motor Fin Mounts.
	CMCP207 Adhesive Dispenser For CMCP206 Adhesive dispenser for CMCP206 adhesive filler.
	CMCP208 Pack of 12 Mixing Nozzles for CMCP206, CMCP207 For Dispensing CMCP206
	CMCP210 Acrylic Adhesive Bypacs For mounting accelerometer mounting pads to the machine
	CMCP211 Depend 330 Adhesive and Activator For Accelerometer Mounting Simple, easy to use solution for gluing CMCP200 Accelerometer Mounting Pads to a machine surface. Each kit will mount 25-50 pads.
	CMCP212 Silicone Dielectric For proper accelerometer mounting
	CMCP213 Clear Silicone Sealant For Accelerometer Mounting - Tube
	CMCP220 Accelerometer Adhesive Mount Kits Everything needed to mount multiple accelerometers
	CMCP230 Accelerometer Mounting Studs Various studs to fit any accelerometer
	CMCP250 Accelerometer Mounting Kit Mounting Pad and Motor Fin Mount + Accessories
	CMCP265 Termination Junction Boxes The CMCP265 series Termination Junction Boxes are multiple channel connecting centers for terminating the outputs of accelerometers or other transducer field wiring.
	CMCP270 Piloted Spot Reamer Disposable low cost tool for facing machines for accelerometer mounting.
	CMCP271 Indexable Counterbore Kit Replaceable cutting blades for multiple uses. The CMCP271 Indexable Counterbore Kit does the same function as the CMCP270 above but has replaceable cutting teeth and can spot ream many more locations for accelerometer mounting. Recommended if you have more than 20 accelerometers to mount.
	CMCP272 Stainless Steel Wire Clips
	CMCP273-01 1/16" Diameter Heat Shrink Tubing - 25x 48" Pieces
	CMCP280 Explosion Proof Accelerometer Housing Accelerometer housing to meet API-670 standards
	CMCP602A Armored 2-Pin Accelerometer Cables The CMCP602A Armored Extension cables are Teflon coated and designed to work with all Accelerometers using a 2-pin MIL Spec 5015 connector.
	CMCP602L Standard Accelerometer Extension Cables For all accelerometers that use a 2 Pin MIL Spec 5015 Connector
	CMCP602H High Temperature Accelerometer Extension Cables For all accelerometers that use a 2 Pin MIL Spec 5015 Connector
	CMCP603A Armored 3-Pin Accelerometer Cables The CMCP603A Armored Extension cables are Teflon coated and designed to work with all Accelerometers using a 3-pin MIL Spec 5015 connector.
	CMCP603C 3-Pin M8 Accelerometer Extension Cables The CMCP603C extension cables are designed to work with all the CMCP1100C line of Accelerometers using a M8 3-Pin connector.
	CMCP603L Standard Accelerometer Extension Cables For all accelerometers that use a 3 Pin MIL Spec 5015 Connector
	CMCP603H High Temperature Accelerometer Extension Cables For all accelerometers that use a 3 Pin MIL Spec 5015 Connector
	CMCP604L 4-Pin Triaxial Accelerometer Extension Cable The CMCP604L extension cables are designed to work with STI's CMCP1300 Series Triaxial Accelerometers using the MIL Spec 26482 4-Pin connector.